Finally slide the top in and screw it to the already mounted top. You will need this screw only to fix the clothes rails in corner modules or larger modules (more than 110 cm wide). For the other door of this module, hinges with 180 opening are provided (please note: they are not delivered already assembled). Attention: Mount the handle precisely and straight! Screw the four pins into the indicated holes. << /Length 9 0 R /Filter /FlateDecode /Type /XObject /Subtype /Form /FormType Then mount the handle with the supplied screws. Important: Mount the clothes rail either under a shelf or under the top cover of the wardrobe and as centrally as possible in the wardrobe depth. In this way, you will get two protruding edges on the front of the door; these edges are necessary for the security of the mirror door itself. Make sure that the drawers and the shelves are not installed where are the hinges of the doors (unless it is a cabinet with only one door) are attached. %%EOF Unpack the base (F) and the top cover (E). To assemble the corner module, please watch carefully the video at this link; below we repeat only a few fundamental points. The drawer module is not attached separately, but is stable due to its weight and usually standing behind the door hinges. Screw the supports for the shelves to the side panel of the bookcase. It is noticeable to you when you set it up. endobj Then position the element inside the wardrobe: either place the drawer module on the cupboard floor or mount it at a higher point: To place it further up, place it on a shelf. Screw from underneath the top cover of the sideboard, until you reach the top. We also remind you that during the installation phase all the regulations in force for the respective countries in terms of safety must be respected. To determine the position of the hinges, one of the doors was already installed. In certain cases, instead, due to the reduction in depth and high height, it is mandatory to mount them on the wall. The hinges are simple to insert and must be attached to the doors using a hammer. hbbd```b``"SA$gRfH0&`RL/E f"dfl`2@ Wardrobeswith a depth of less than 45 cm must be fixed to the wall to ensure a greater stability and safety. << /Type /Page /Parent 4 0 R /Resources 7 0 R /Contents 5 0 R /MediaBox [0 0 841.89 595.276] Since the same LED lengths are used for different cupboard heights, it can happen that a small part of the lower, vertical LED bar is covered by the wardrobe base. Please note that there must be some space available for the transformer of the LED systems! Carry out this step both in the base and the top cover. This leaves a small gap between the cover shelf and the top drawer. If you also ordered LED lights, please note the following before setting up: The horizontal sensor LED bar with motion detector (see video) is mounted under the wardrobe cover at the top (inside the cabinet). Attention: At the end of the assembly it is essential that the pre-holes, which will be used to fix the shelves, are located in the corner component on the right as shown in the photo and in the video. In the package, you will find also metal bars, which have to be placed and screwed on the edge of the door (one on the upper edge and the other on the lower edge). In any case, you have to begin with the assembly of the outer side panel, which will not stand behind the bookcase. The third variant for the free standing wardrobe as for fitted wardrobe is to accommodate the transformer on the top of the cabinet cover: However, this is only possible if, in addition to the necessary centimetre that is required for the construction, there is about 2 cm more space up to the ceiling. endobj Now unpack the first door in the appropriate width. Screw the four pins (see photo below) into the indicated holes. Information on the authenticity of customer reviews. Attention, these are not identical! The drawer boxes have a slightly lower depth than the shelves and can be set up flush at the front. Before proceeding with the installation, it will be the customers duty to collect all useful information for assembly using the videos and assembly instructions provided by IDAW. Loosen screws A slightly to raise or lower the respective door. 8 0 obj Use a screwdriver to open the milled groove, into which the back side of the wardrobe will later be inserted, up to the edge (see drawing below). : IT 05173760280, Montefiori s.r.l. Attention: The smallest corner base measures 49.6 cm (video). Attach the leveling feet only on the side facing the inside of the wardrobe. Place the top on the top cover of the sideboard and screw it with self-tapping screws (35 mm long). Then drill from the outside in using a 5 mm drill bit and enlarge the hole. For the corner doors, hinges with 180 opening are provided (please note: they are not delivered already assembled). A shelf serves as the cover shelf and support for the drawer box: it is either attached like the other shelves. In order to assemble this wardrobe, you can start with the corner module, and then continue with the other linear modules on the sides of the corner. 3) Proceed with the assembly of the right part of the corner. Attention: Before proceeding with the assembly of the corner wardrobe, you must also watch the more detailed video on assembling a linear wardrobe and read the general instructions. Please do not just proceed by looking at the pictures alone! Proceed in the same way with all wardrobe side dividing panels up to the last right outer side panel on the right-hand side of the wardrobe, where pins and leveling feet are mounted on the left-hand side (towards the inside of the cupboard). If you have 1 cm of space between the hat and the ceiling, proceed as follows: First insert the back panel, then slide the longest top in and hook it only to the wooden pins (without using the metal pins). Please note that this step must be carried out by two people! 0 If necessary, assembly the handles (the handles are already milled in the integrated door variant). (video). The width is noted on the label on the box. See also our montage film. Usually, our closet does not need to be wall-mounted as it is quite heavy and stable. Now take care of the hinges for which there is no pre-drilled hole: Unscrew not much the vertical screws of the door hinges that still have to be mounted. In the case of a corner solution with 2 linear wardrobes (one with depth 45cm and the other one with depth 61cm): The 61 cm deep wardrobe stands directly against the corner wall. Check whether the base and cover are correct for the respective module by comparing the dimensions with the drawing on the first page. endstream endobj 189 0 obj <>>> endobj 190 0 obj <>/ExtGState<>/Font<>/ProcSet[/PDF/Text]/Properties<>>>/XObject<>>>/Rotate 0/TrimBox[0.0 0.0 595.276 841.89]/Type/Page>> endobj 191 0 obj <>stream If not, please continue on with point 11! The shelves are mounted with the screws shown in the photo. With firm pressure and horizontally, just screw these screws into the dividing side panel. 2) Use the double-sided tape to first attach the mirror to the door. If you do not have much space above the wardrobe, screw the holders for the clothes rail now before fixing the top to the wardrobe. (here the video). The last option is to cut a cutout for the transformer in the wardrobe back: This has the advantage that it is easily accessible. First screw the pins all the way in and then turn them back a little until the two holes are positioned vertically. 5 0 obj (video). Continue by inserting the left side panel of the corner module. Close the doors of the wardrobe, then switch off and on the general electric panel of the house, so that the sensors work correctly, when you open the doors. Proceed in this way: Position the door exactly. This is useful for stabilizing the top and the angle, since no pins are used. The paint can be used to make small touch-ups, if necessary. Now connect the side panel of the bookcase to the wardrobe outer side panel (attention: for this step, you need someone to hold the other side of the top up). First assemble only one door (with two people) by screwing the hinges on the wardrobe to the dividing side panel. Thank you . If you want to assembly the feet, which is not absolutely necessary, turn the module over and carefully turn it upside down (this step was not shown in the photos) to assembly them. In this case, put some tape in two points of the top cover of the sideboard (about 5 cm from the edge, both on one end of the top cover and on the other one) and lay the top on the sideboard. - Company subjected to the activity of management and coordination of IDAW s.r.l. Once the goods have been unloaded and received, their care is responsibility of the customer. Wardrobe Made to Measure, Fitted Wardrobe and Roof Pitched cabinet, Assembly instructions and videos of the wardrobes, Video Montage Freestanding Wardrobe / Fitted Wardrobe, Video Montage Wardrobe with sliding doors and integrated TV, Assembly and installation videos Accessories, Assembly of the trouser hanger (pull-out) / belt / tie extension, Handle K panel handle, entire door length assembly, Fixing the cabinet doors when missing hinge holes, IDAW installation of the fitted wardrobe side panels, Fitted wardrobe: building instructions feet of the last side wall, Videos Wardrobe, Chest of drawers and Accessories, Installation of the vertical LED bar (in the dividing side panel), Assembly instructions: Freestanding wardrobe, IDAW s.r.l. Or it is also possible to mount the corner module starting from a linear module, which was assembled previously. That is why this enables the back side of the wardrobe to be inserted laterally. ( -?U1seP;dL188Cb-V~6}ww{wq~?-6n6rX~%vo{o_{K?o stream &{iHg` ` ` Attention: As long as the left side panel of the corner module is not mounted, the top is movable; therefore pay particular attention during this step. You will also receive a sheet with adhesive circles. Horizontal LED strips: For the power cable, a hole should be drilled into the wardrobe top cover on the left outside the position where the LED bar is to be screwed on, so that the power cable can be routed above and behind the wardrobe to a socket. 1 /BBox [11 13 835 581] /Resources 10 0 R /Group << /S /Transparency /CS /DeviceCMYK Do not tighten the screws immediately one after the other, but screw them in step by step, i.e. endobj (video) (video). 1) First, take the two pieces that form the corner and assemble them together with the supplied pins and wooden pins. The hinges are simple to insert and must be attached to the doors using a hammer. The easiest way to accommodate the narrow transformer is behind the dividing side panel if there is at least 3 cm of space between one of the wardrobe dividing side panel and wall behind the side cover panel (when you have ordered fitted wardrobe). 4) Finally, cover the screws with the screw covers provided. If there are no holes for the leveling feet: /I true /K false >> >> << /Length 6 0 R /Filter /FlateDecode >> First screw the pins all the way in and then turn them back a little until the two holes are positioned vertically (see the photo with the arrows below). (video), Put in the base and the left outer side panel together and tighten the screw shown below. Any unauthorized modification made to the wardrobe structure and its components or any improper use of the product will automatically void the product warranty as our cabinets must be installed following the instructions provided and respecting their normal working and use. It will therefore be necessary to use all the necessary personal protective equipment in order to guarantee a safe assembly. 188 0 obj <> endobj Mount the leveling feet as shown in the drawing (right side). Then, connect the outer side panel to the structure of the wardrobe, and screw. Pay attention to the correct position of the pins and the holes. Alternatively, you can use some double-sided tape. On the left door of the corner module, magnets will be fixed both on the base and on the top of the wardrobe (see video). Please be careful not to unscrew them completely! IDAW cannot be held responsible for damages deriving from improper use or modifications made to the product. The door is correctly installed if there is 1.6 cm of space between the floor and the door! 6 0 obj In case of mirror doors: Continue by inserting the left side panel of the corner module. endobj xruy":^C\l`(U Depending on the colour of your closet, you will receive a bottle or a can of paint. Attention: If you want to insert a clothes rail under the top of the corner module, proceed as follows (see video): Attention: If the cover cannot be pushed in, check whether both the holes and the pins are correctly positioned as described above. In order for the motion sensor to work properly, it must always be positioned at the top. If there is space above the top, fix the bookcase to the wardrobe from above with metal angles. Only a few steps are required (see photos below). Pay attention to the correct positioning so that the pins can be inserted later (in the base and top cover of the wardrobe). stream When opening the package of metal parts, small parts and fittings, please ensure that no part is lost, since the parts are counted exactly and are only available in the number required for assembly. This step concerns only the assembly of a sideboard. If the height of the wardrobe ordered differs from a standard size, pre-drilled holes for mounting the hinges on the dividing side panel of the wardrobe may be missing. Unpack the shelves, the base and the top of the bookcase. Repeat the same procedure for the other side panel. %PDF-1.3 % Using an 8mm drill point, make a hole in the top from the side facing the ceiling. If you have more than 2,5 cm space between the top and the ceiling, proceed as follows: Insert the back panel first, then slide the longest top in and raise it as much as needed to hook it onto the pins and the wooden pins. Be sure to start at the top, 2.5 cm below the end of the dividing side panel, on which the cupboard top cover will be attached later, when you insert the vertical LED bar in the horizontal wardrobe dividing side panel. Then put the feet on and turn the module over again. The drawer boxes (with 2 or 3 drawers), the chest of drawers, the bedside table and the 7-drawers chest of drawers are delivered to the customer already assembled. alternately, at the same time. IMPORTANT: Glue ordinary furniture felts (not included) to the bottom of the leveling feet to avoid the wardrobe from scratching the floor when it is moved. Attention: these screws are not supplied). The package includes a longer screw as well. It should not be confused with the base of a possible 50.2 cm wide linear module. Insert the corner into the base and fix it with the pins and dowels. 3 0 obj The leveling feet create a leveling of up to 5 mm. This will help you to avoid assembly difficulties! - C.F. Now assemble the corner as shown in the video: With a straight plate junction with 4 holes fix the top with the angle. Then tighten the screw again. Loosen screw C slightly to increase or decrease the distance between the door and the wardrobe module. (video) (video), Fasten each clothes rail holder to the side panel with two screws on the side. 2)This step must be done in two people with the utmost attention and safety! The enclosed wooden dowels are only used if you install two drawer modules one above the other. Drill slowly outwards on the pre-holes with a 3 mm wood drill and little pressure. Assemble all accessories firstly (when one door of the wardrobe is already assembly). Extras and accessories: more overview more order! If the top of the bookcase is less than 3cm from the ceiling: Install the screw covers: place them on the larger holes so that they are covered. 3) Attach the mirror to the door by tightening the security screws with a screwdriver (not an electric screwdriver to avoid breaking the mirror). Now insert and tighten the screws. A second person should check that the drilling is being carried out perfectly in horizontally to the door. (video), Insert the metal components into the holes shown below. Assembly instructions: Freestanding cabinet, Please take the time to read the instructions. The shelf can also just be put on if you prefer. Insert the various elements. Alternatively, it can be placed behind the wardrobe back if the wardrobe can be set up approx. The person who performed the installation must attach it to the wall before installing the door to avoid the risk of falling forward. (video), Unpack the back side of the wardrobe (C) and select the right one with the appropriate width for the respective module (the back side of the wardrobe is approx.1.5 cm wider than the module, as it is inserted into the milled groove in the cabinet side panels, base and top cover). Unpack the side panels of the bookcase. 1) First decide where to position the mirror. 7 0 obj Then tighten the screws again. The drawer module for installation inside the wardrobe is almost completely assembled. hb```f``e`e`hdb@ !$..u,n6kL SxEOM/Y kk,:Hy[|L',8g;MNBfa>q_UH%X]yZ3SD?k, CGGGG D1@[ZD"KK2*` FO0m EX ~f7|/93&Yg^ b oe04hkK [Y7#$A\|(|@ +x (video) Continue with the assembly of the other parts of the module. The shelf clicks into place and is thus firmly stabilized. Please open the packages in the order listed. The customer must not disassemble the drawers in any way, but will simply have to follow the assembly instructions. Attention: if you have also ordered a side bookcase, read point 20 right now (for the assembly of the bookcase and of the wardrobe outer side panel, on which the bookcase will stand). (video). Use the two supplied screws for this. Use the Hex (Allen) key (included) and a spirit level to position the wardrobe horizontally. 05396590282, EUROMOEBEL NEWLINE GMBH VAT NUMBER:CHE-114.608.208 Letziweg 9, 4663 Aarburg. /Rotate 0 >> %PDF-1.4 % These can be used to cover any visible holes, for example if you decide to move a shelf. The vertical LED bar, in the dividing side panel (see video), is installed in the inner cheek in which the milling is provided for this at the factory. With the help of a ruler, mark the points where the feet will be fixed; help yourself by referring to the base (or to the top as in the video). on the right side). In the modules with two doors, the left door has a plastic dust protection. Now mount the other side panel of the bookcase as well. With a drill with a 9mm tip, make the holes for the feet. 229 0 obj <>stream endstream Place the longest part of the corner base on the ground. For safety and practical reasons, please note the following: To avoid damage to the material and accidents, the cabinet should be assembled by two people. For this, the milled groove on the edge must be opened. If necessary first remove the cover and correct the position of the holes and pins. IdNr. Now fix the hinges, which find their place on pre-drilled holes, by screwing in the vertical screws. Screw th four pins i the holes on the lacquered side as well. Please proceed precisely to ensure that they can be connected easily later. In our video you can see how to assembly it with the wardrobe dividing side panel hole already prepared; however, it is much easier to install on a cupboard dividing side lying on the floor or on the table. 47 2 cm forward. Once you have assembled the whole wardrobe, reset the LED lights, while the doors are closed. In this wardrobe, the door of the last module (with normal hinges and without handles) will not be usable. x+TT(T0 BC=KSKS=#s3Tp}\C|@ s After the drawer element has been positioned in the cabinet, first place the closing strips on the left and right on the wooden pins provided and tap them into place (Attention: in the photos, the strips were installed outside the wardrobe, which you should do better rather than inside the wardrobe). Now unpack the side dividing panel of the wardrobe, assemble the two cupboard feet (dont forget the furniture felts) and screw in the pins on both sides. Insert the back side of the wardrobe and the top cover into the milled groove and then slide the top cover to the left up to the left side of the cupboard until the pins enter the holes. Install the door slow motion (one for each wardrobe door): The door slow motion is simply clipped to any door hinge, it must be a sufficient blow if it is necessary to use a rubber hammer AFTER it has been used or positioned correctly. Uninominale - UST. endstream endobj startxref Then insert the screws. First attach the leveling feet (see the photo) to the first left outer side panel only on the side facing the inside of the wardrobe (i.e. Please proceed precisely to ensure that they can be connected easily later. In the second case, the brush is not included. q ouo/T\. If you have ordered a drawer element, the instructions follow here. Furthermore, IDAW cannot be held responsible for any damage caused after delivery or during assembly. Please do it in two in any case! Unpack the outer side panel of the wardrobe the right (A) or left (A). 211 0 obj <>/Filter/FlateDecode/ID[<335510552F0C5142814019CE5D4A8A62><822AA58277469A418FC320F98D256C88>]/Index[188 42]/Info 187 0 R/Length 110/Prev 1513600/Root 189 0 R/Size 230/Type/XRef/W[1 3 1]>>stream Put in the side panel of the bookcase and the wardrobe outer side panel together and tighten the screws. (video). Before mounting the bookcase side panel to the outer side panel of the wardrobe, hook one side of the top to the side panel while it still lays on the work table. This step concerns only the assembly of the bookcase. (video) Be careful with the next step! Then, insert the other side panel of the bookcase and hook the top from underneath. hVYo8+|LP. An important piece of information about the custom-made cabinet with depth of 45 cm or less. (Video Side Bookcase Assembly). (video). Put on the top cover element with the help of a ladder. Turn screws B in or out to move the door left or right. Insert the smaller base and screw it to the larger base; then insert the back panel. Unpack the outer side panel of the wardrobe. Then, insert the metal components into the holes on the innerside of the side panel and the wooden pins along the edge of the panel. << /ProcSet [ /PDF ] /XObject << /Fm1 8 0 R >> >>

Sitemap 19

manual for fixing wardrobe