With your number, letter, or plaque order,well include instructions, mounting hardware, and a handy drilling template. Set! Use a ruler to measure the space between each number. Keep guidelines straight, maintain your desired spacing. Need Help? Press numbers firmly onto mailbox. Take care not to scratch the face of the number. Press stencil decal firmly with even pressure onto concrete at desired location. Drill holes according to template. Matte Black Aluminum Floating or Flat Modern House Number 1, 6 in. For horizontal arrangement, go to step 2A. Note: decal should not be applied on rough surfaces or in wet, freezing conditions. Push studs into pre-drilled holes on the back of the number. Use clear tape to connect individual templates together. Aged Bronze Screw On House Number 4, 6 in. Aged Bronze Screw On House Number 2, 6 in. Rinse gently with clean, fresh water. Adequately protect adjacent surfaces with paper. Clean and dry the mailbox surface. Clean surface of all loose debris. Apply a thin layer of epoxy to one end of the stud. For decals, it doesnt get any easier than peel-and-stick! Skip to step 4. Gather supplies: house numbers, template, studs, spacers, (not included: tape, epoxy, rubber mallet, drill, level). Matte Black Aluminum Floating or Flat Modern House Number 2, 6 in. Use a soft cloth and a mild household detergent solution to remove dust, salt, and other deposits. Tape all edges. Align templates vertically using labeled vertical guideline. Allow paint to dry. Align templates horizontally using labeled guidelines at top and bottom. Dry with non-abrasive towel. If so, place on a soft surface. Dry with non-abrasive towel. Light tapping with a rubber mallet may be required. Push studs into pre-drilled holes on the back of the plaque. Overlap of paper template edges is to be expected. Push number into holes. Carefully remove template. Place a piece of tape to align the bottom edge of the numbers. Gather supplies - curb stencil decal, (not included: spray paint, paper roll and masking tape). Products shown as available are normally stocked but inventory levels cannot be guaranteed, For screen reader problems with this website, please call 1-800-430-3376 or text 38698 (standard carrier rates apply to texts), 6 in. Determine your desired spacing between numbers on the available space. Tape template at desired location. Ready? CARING FOR YOUR PRODUCTS: To extend the effective life of your numbers, clean them every six months or every three months in coastal or industrial regions. Note: decals should not be applied on rough surfaces or in wet, freezing conditions. Gather supplies: tape and ruler (not included). Aged Bronze Screw On House Number 3, 4 in. Aged Bronze Screw On House Number 5, 6 in. Instructional video of how to install your modern house numbers on a stucco wall. No spacers were used. Rinse gently with clean, fresh water. Masonry, concrete, and stone installations may require a hammer drill. Use of this site is subject to certain Terms Of Use. Continue to Numbers Installation . Peel off the front transfer film. Keep vertical guidelines aligned. Use a level to align template. Take care not to scratch the face of the plaque. Please call us at: 1-800-HOME-DEPOT (1-800-466-3337), Please enter in your email address in the following format: you@domain.com. Spray paint stencil using multiple, light coats. Arrange individual paper templates in desired order. Masonry, concrete, and stone installations may require a hammer drill. CARING FOR YOUR PRODUCTS: To extend the effective life of your plaque, clean every six months or every three months in coastal or industrial regions. Note: Steel studs must be fully concealed to protect from the elements. Get exclusive access to new products and deals. Aged Bronze Screw On House Number 0, 6 in. Slowly peel off the clear, front transfer film. Aged Bronze Screw On House Number 1, 4 in. Apply a thin layer of epoxy to the end of the exposed studs. Once dry, slowly remove stencil. Step 4 Push number into the mounting holes. Step 2 Screw in the threadedstuds into the back of the number. Proudly Made in USA. Step 3 Slide spacers over studs and apply epoxy or clear siliconeto the end of the stud. Set! Note: Steel studs must be fully concealed to protect from the elements. This is your drilling guide. The below Instructional video demonstrates how to install aluminum powder coated letters on an office wall. Overlap of paper template edges is to be expected. Local store prices may vary from those displayed. For vertical arrangement, skip to step 3A. Take care to not scratch the face of the number. Go time. All Rights Reserved. Aged Bronze Screw On House Number 6. Gather supplies: mailbox numbers, (not included: tape, and ruler). If so, place on a soft surface. Peel off number backing. Overlap of paper template edges is to be expected. Go time! With your number, letter, or plaque order. Light tapping with a rubber mallet may be required. Push plaque into holes. Take care not to over spray. Drill holes according to marks on the template - use 3/16" drill bit. For decals, it doesnt get any easier than peel-and-stick! For a worry-free install, get acquainted with our step-by-step installation instructions! 2000-2022 Home Depot. Please note that these letters are mounted flush on the wall. Light tapping may be required. Use 11/64 drill bit or specialty 3/16 bit for masonry and rock. Unsubscribe at any time. Apply even pressure along the entire surface. With your order, you'll receive our custom-made modern house numbers/letters, threaded aluminum studs, 1/2 inch aluminum spacers (which give your numbers that "floating" look), pre-printed mounting template, and printed instructions on an easy step-by-step process for installing your modern house numbers. Note: Curb stencil should not be applied in wet or freezing conditions. Slide spacers over studs. Aged Bronze Flush Mount House Number 1, 6 in. Align X marks on each template at top and bottom to achieve equal spacing between each number. 2021 Modern House Numbers well include instructions, mounting hardware, and a handy drilling template. Aged Bronze Flush Mount House Number 2, 6 in. Peel off the number backing and align with tape guide. Use a soft cloth and a mild household detergent solution to remove dust, salt, and other deposits. For a worry-free install, get acquainted with our step-by-step installation instructions! Take care to not scratch the face of the plaque. Installation Instructions Step 1 Tape the paper mounting template to the desired location and use a level to align template. Measure the desired number location. Remove tape. Ready? Light tapping may be required. Gather supplies: plaque, template, studs, spacers, (not included: tape, epoxy, rubber mallet, drill, level).

Sitemap 15

floating mount house numbers